Emerson Rosemount Oxymitter DR Reference Manual Download Page 42

Page: 42 / 98

Table 2-8: Replacement Parts

(continued)

Number in

Figure

2-15

Part name

Pressure

Part number

Combination filter-
regulator

0-30 psig

4505C21G01

Instrument air (reference air): 10 psig (68.95 kPa) minimum, 225 psig (1551.38 kPa)
maximum at 2 scfh (56.6 L/hour) maximum; less than 40 parts per million total
hydrocarbons. Set regulator outlet pressure at 5 psa (35 kPa).

2.4

Set up probe with electronics package

You can use the Rosemount

™

Oxymitter DR probe with several electronics packages,

including: Models 218, 218A, 225, 132 (analog and digital), TC200, and ZA8C.

WARNING

Failure to install covers and ground leads could result in serious injury or death.

Install all protective equipment covers and safety ground leads before starting the
equipment.

2.4.1

Set up Westinghouse Models 218, 225, and 132
(analog) electronics

Change the probe heater setpoint of the existing electronics to support the Rosemount

™

Oxymitter DR probe.

Procedure

1. Open electronics enclosure.
2. On temperature controller card, connect jumper wire from TP3 to either Pin 2 or Pin

Install

Reference Manual

October 2019

00809-0100-4880

Emerson.com/Rosemount

Summary of Contents for Rosemount Oxymitter DR



































































































Search results

Summary of Contents for Rosemount Oxymitter DR

Reviews:

Related manuals for Rosemount Oxymitter DR

Brands by name

Popular brands

Emerson Rosemount Oxymitter DR, Reference Manual

Search results

Summary of Contents for Rosemount Oxymitter DR

Reviews:

Related manuals for Rosemount Oxymitter DR

Brands by name

Popular brands