manualshive.com logo in svg

Emerson Rosemount Oxymitter DR, Reference Manual

Share
Download
Emerson Rosemount Oxymitter DR Reference Manual Download Page 91

C

Rosemount

™

 Oxymitter

™

 product

certifications

Rev 2.0

C.1

European Directive information

The most recent revision of the EU Declaration of Conformity can be found at

Emerson.com/Rosemount

.

C.2

Ordinary location certification

As standard, the transmitter has been examined and tested to determine that the design
meets the basic electrical, mechanical, and fire protection requirements by a nationally
recognized test laboratory (NRTL) as accredited by the Federal Occupational Safety and
Health Administration (OSHA).

C.3

Installing equipment in North America

The US National Electrical Code

®

 (NEC) and the Canadian Electrical Code (CEC) permit the

use of Division marked equipment in Zones and Zone marked equipment in Divisions. The
marking must be suitable for the area classification, gas, and temperature class. This
information is clearly defined in the respective codes.

C.4

Rosemount

™

 OXT4A Oxymitter for general

purpose locations and OXT4C hazardous
locations certification

Rosemount Oxymitter Oxygen Transmitters (Series 4000 & DR): OXT4A, OXT4ADR,
OXT4C, OXT4CDR, OXT4CNF, and OXT4CDRNF and Rosemount Oxymitter 4000 series
6A00095G05, 6A00095G06, 6A00094G07, and 6A00094G08

C.4.1

USA/Canada

CSA Certificate

1238566

Standards

CSA C22.2 No. 30-M1986 (R1999), CSA C22.2 No. 213-M1987, CAN/
CSA-E600079-0:02, CAN/CSA-E60079-1:02, CAN/CSA-E79-7:03, CAN/
CSA-C22.2 No. 61010-1-12, UL Std. No. 1203 Ed. 3, ANSI/ISA
12.12.01-2013, UL 61010-1 (3rd Ed.), ANSI/ISA 12.16.01-1998,
ANSI/ISA 12.00.01-2002, ANSI/ISA 12.22.01-2002

Markings

Reference Manual

Rosemount

™

 Oxymitter

™

 product certifications

00809-0100-4880

October 2019

Rosemount Oxymitter DR

91

Summary of Contents for Rosemount Oxymitter DR



































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands