Emerson Rosemount Oxymitter DR Reference Manual Download Page 35

Page: 35 / 98

Figure 2-12: Installation with Drip Loop and Insulation Removal

A. Line voltage.

B. Logic I/O 4-20 mA signal.

C. Drip loop.

D. Stack or duct metal wall.

E. Mounting plate.
F. Insulation.

G. Replace insulation after installing Rosemount Oxymitter 4000.

4. If the system has an abrasive shield, check the dust seal gaskets. Make sure the

joints in the two gaskets are staggered 180 degrees and that the gaskets are in the
hub grooves as the transmitter slides into the 15 degree forcing cone in the abrasive
shield.

Note

If process temperatures will exceed 392 °F (200 °C), use anti-seize compound on the
stud threads to ease future removal of the transmitter.

5. Insert probe through the opening in the mounting plate and bolt the unit to the

plate.

Note

To maintain CE compliance, ensure a good connection exists between the
mounting plate studs or earthing screws on electronics housing and earth.

Reference Manual

Install

00809-0100-4880

October 2019

Rosemount Oxymitter DR

Summary of Contents for Rosemount Oxymitter DR



































































































Search results

Summary of Contents for Rosemount Oxymitter DR

Reviews:

Related manuals for Rosemount Oxymitter DR

Brands by name

Popular brands

Emerson Rosemount Oxymitter DR, Reference Manual

Search results

Summary of Contents for Rosemount Oxymitter DR

Reviews:

Related manuals for Rosemount Oxymitter DR

Brands by name

Popular brands