Emerson Rosemount Oxymitter DR Reference Manual Download Page 27

Page: 27 / 98

Figure 2-4: Rosemount Hazardous Area Oxymitter 4000 Probe with Abrasive Shield

Note

These flat faced flanges are measured to ANSI and DIN patterns and are not pressure
rated. All dimensions are in millimeters with inches in parentheses unless otherwise noted.

A. Dimension A (see

Table 2-3

)

B. Dimension B (see

Table 2-3

)

C. Snubber/dust seal assembly

D. Deflector assembly

E. Diffuser/dust seal assembly
F. 91 (3.6) diameter nominal

NPT electrical connection

Table 2-3: Installation/Removal

Probe

Dimension A

Dimension B

18 in.

387 (15.3)

912 (35.9)

3 ft.

842 (33.2)

1367 (53.8)

6 ft.

1762 (69.4)

2287 (90.0)

Table 2-4: Abrasive Shield 3D390003

Flange

ANSI

DIN

Flange diameter

229 (9.0)

235 (9.25)

Hole diameter

19 (0.75)

24 (0.94)

8 holes equally spaced on BC

191 (7.50)

190 (7.48)

Ref air

Cal gas

(1)

ANSI

-in. tube

DIN

-in. tube

(1)

Add check valve in cal gas line.

Reference Manual

Install

00809-0100-4880

October 2019

Rosemount Oxymitter DR

Summary of Contents for Rosemount Oxymitter DR



































































































Search results

Summary of Contents for Rosemount Oxymitter DR

Reviews:

Related manuals for Rosemount Oxymitter DR

Brands by name

Popular brands

Emerson Rosemount Oxymitter DR, Reference Manual

Search results

Summary of Contents for Rosemount Oxymitter DR

Reviews:

Related manuals for Rosemount Oxymitter DR

Brands by name

Popular brands