manualshive.com logo in svg

Emerson Rosemount Oxymitter DR, Reference Manual

Share
Download
Emerson Rosemount Oxymitter DR Reference Manual Download Page 36

6. Ensure the transmitter is properly earthed by way of both internal and external

points.

 CAUTION

Uninsulated stacks or ducts may cause ambient temperatures around the
electronics to exceed 185 °F (85 °C), which may cause overheating damage to the
electronics.

If you remove duct work insulation for transmitter mounting, replace the insulation
afterwards. See 

Figure 2-12

. Ensure the probe installation does not obsure the

warnings on the housing covers.

2.2

Electrical installation with integral electronics

All wiring must conform to local and national codes.

 WARNING

Disconnect and lock out power before connecting the unit to the power supply.

 WARNING

Failure to install covers and ground leads could result in serious injury or death.

Install all protective equipment covers and safety ground leads after installation.

 WARNING

To meet the safety requirements of IEC 61010 (EC requirement) and ensure safe
operation of this equipment, connect to the main power supply through a circuit
breaker (minimum 10 A) which will disconnect all current-carrying conductors during a
fault situation.
Make sure this circuit breaker includes a mechanically operated isolating switch.
If there is no switch, locate another external means of disconnecting the power supply
close by.
Circuit breakers or switches must comply with a recognized standard, such as IEC
60947.

 WARNING

The instrument is heavy.

Use proper lifting and carrying procedures to avoid personal injury.

Install

Reference Manual

October 2019

00809-0100-4880

36

Emerson.com/Rosemount

Summary of Contents for Rosemount Oxymitter DR



































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands