Elster A1120 User Manual Download Page 127 | Manualshive

Page: 127 / 157

background image

28

A1120/1140 Programmable Polyphase Meter Users Manual

___________________________________________________________________

4.1.1

Data Stream Mode

Data Stream Mode allows data to be read back from
the meter via the serial port and optical
communications port much faster than the normal
Data to Read mode. Data Stream Mode is available
to read all data.

To use the Data Stream option via the serial port,
the Serial Port configuration in the A1120/40
options/communications page must be set to 8
(eight bits), none (no parity), 1 (one stop bit)

4.2 Readings

Viewer

The Readings Viewer allows data read back from a meter to be examined.

To View the Readings

Double click on the new data to read in the scheme manager

Double click one of the readings to view the data read back from the meter.

Generally these are displayed in a similar format to which the data is entered.

©

Elster Metering Ltd - M181 001 3C - 12/2007

«
...
125
126
127
128
129
...
»

Summary of Contents for A1120






























































































































































Reviews:

No comments

Related manuals for A1120

Brand: Omer Pages: 2

Brand: NARDA Pages: 64

Professional Plus

Brand: YSI Pages: 28

Duomat Evolution DeLuxe

Brand: Dennerle Pages: 27

Brand: Seaward Pages: 2

DigiFlow 6710M-22

Brand: Savant Pages: 3

Brand: Osaka Pages: 3

Brand: SIKA Pages: 8

Brand: OHAUS Pages: 6

Brand: Alpes Lasers Pages: 41

Brand: Thermo Scientific Pages: 56

Brand: Velleman Pages: 15

WTW pH/ION 3310

Brand: Xylem Pages: 48

Brand: NARDA Pages: 14

Privia PX-860BK

Brand: Casio Pages: 67

Brand: HOKUYO AUTOMATIC Pages: 17

Brand: ScienTECH Pages: 44

Xtrinsic MMA8491Q

Brand: Freescale Semiconductor Pages: 4

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands