Elster A1120 User Manual Download Page 30 | Manualshive

Page: 30 / 157

background image

22

A1120/40 - Electronic Polyphase Meter

©

Elster Metering Limited - M181 001 2G - 5/2010

13.2.6 CT Ratio Programming

The CT ratio can be displayed as a ratio or as a scalar quantity. A count of the number of CT
Ratio reprogramming events to a maximum of 65,535 is recorded together with source (Optical or
RS232 port) and time and date stamps for the three most recent events. The identity of the
programming user is also stored. The count and time and date stamp can be included in the
display sequence.

Note: CT Ratio Reprogramming Events are communications sessions where the primary or
secondary value of the CT has been changed.

An End of Billing Reset can be requested with a CT ratio change.

A CT Programming switch can be fitted as a manufacturing option. The switch must be activated
in order to change the CT ratio. The switch is under the terminal cover and may be protected by a
paper seal.

13.2.7 Watchdog (Transient Reset)

A count of the number of watchdog resets to a maximum of 65,535 is recorded together with time
and date stamps for the three most recent events. The count and time and date stamps can be
included in the display sequence.

13.2.8 In Service Hours

The elapsed time counter records the cumulative time (to a resolution of 1 hour) the meter has
been powered up. The count can be included in the display sequence.

The amount of storage is in excess of 25 years.

13.2.9 Meter

Errors

An alarm can be displayed if an error occurs. The alarm and error message
(See Figure 8, Display table) can be disabled via the Power Master Unit.

Access to the data is via the optical port, the RS232 data port or on the LCD.
A time and date stamp of the three most recent non-fatal error events is recorded where possible.

In the unlikely event that any of the above meter errors occur, a catastrophic failure has been
detected and the meter should be returned to Elster Metering for failure investigation.

13.2.10 Cover Removal Detection

Main Cover

As a manufacturing option the main cover can be fitted with a tamper switch to detect removal.
The number of times the cover has been removed to a maximum of 65,535 is recorded together
with the time and date stamps of the last three occurrences. The count and time and date stamps
can be included in the display sequence.

Note: The main cover removal option is not available when the meter is configured for CT Ratio
Programming Switch.

«
...
28
29
30
31
32
...
»

Summary of Contents for A1120






























































































































































Reviews:

No comments

Related manuals for A1120

ORBISPHERE 3624

Brand: Hach Ultra Pages: 12

Brand: Velleman Pages: 96

Brand: Kawai Pages: 40

Brand: Tohnichi Pages: 12

Concert Performer Series Digital Piano CP110

Brand: Kawai Pages: 149

Micropilot S FMR533

Brand: E+H Pages: 12

Brand: National Instruments Pages: 169

sound SMART RLT Sport

Brand: VCA Pages: 36

GRAND RHAPSODY PIANO

Brand: Waves Pages: 19

Tintometer XD 7500

Brand: Lovibond Pages: 164

Brand: Benstone Pages: 222

Brand: Myron L Pages: 2

Brand: Elenco Electronics Pages: 52

Brand: Iradion Pages: 34

Sphensor PRMPA0401

Brand: LSI LASTEM Pages: 32

Brand: Meters UK Pages: 11

Brand: Tektronix Pages: 57

Brand: Hexagon Pages: 30

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands