Elster A1120 User Manual Download Page 139

Page: 139 / 157

A1120/1140 Programmable Polyphase

Meter Users Manual

_____________________________________________________________________________________

To select the comms port

- Select the comms port (1 - 16) then

double click on the type of communications from the dropdown
list.

Auto Detect -

This automatically detects the hardware available

on a selected port and assigns it to the port.

Disable DTR

Various probes can be used to communicate with meters via the optical 'FLAG' communications port.
These probes are one of two basic types:

Probe with DTR disabled

Probe with DTR enabled

It is important to choose the correct probe for your installation, as optical communications will not be
available if the wrong probe is selected.

Modem Init -

If a modem is selected on a port, Modem Initialisation allows the initialisation string to

be set. The modem type (tone or pulsed dialling) must first be selected.

To set the string

, select Modem, select the type of dialling then type the string in the box provided

and press Save

File Location -

To modify a file path, press Modify and edit the file path accordingly.

Use number of retries to set the number of times the computer tries to connect.

Result (.RES) File Management -

This option allows the user to Append new data to a .RES file or

Always overwrite the .RES file with new data.

If Append new data is selected, any new data is added to the .RES file. This option is used if the .RES
files are to be used outside the Power Master Unit.

Note – If this option is used, old readings are stored in the database and new readings are appended.

Always overwrite with new data is the option normally used. This overwrites any old data with the new
data.

Elster Metering Ltd - M181 001 3C - 12/2007

Summary of Contents for A1120






























































































































































Search results

Summary of Contents for A1120

Reviews:

Related manuals for A1120

Brands by name

Popular brands

Elster A1120, User Manual

Search results

Summary of Contents for A1120

Reviews:

Related manuals for A1120

Brands by name

Popular brands