Elster A1120 User Manual Download Page 143

Page: 143 / 157

A1120/1140 Programmable Polyphase

Meter Users Manual

_____________________________________________________________________________________

Methods of Connection

Modem -

Modems are connected to a meter via the RS232 communications port and the Elster

Metering Systems Communications Server. The Communications Serial Port,
Outstation number and Telephone number also require entering.

PAKNET -

PAKNET connects a meter via a PAKNET Radio PAD and the RS232 communications port

and the communications server. The Communications Serial Port, Outstation number and PAKNET
PAD number also require entering.

Flag -

Flag connection allows communication with a meter via the meter's Optical Port.

RS232 -

RS232 connection allows an A1120/40 to be targeted for communications.

The baud rate is selectable. Data Steam Mode allows fast data readings.

CHIRPS -

This option allows CHIRPS files to be created.

To create a CHIRPS file, select CHIRPS, select the Directory where the Chirps files are stored and
press OK

Hand Held Unit -

This allows the Master Unit to communicate with a Hand Held Unit via OMS

software.

Proxy Flag

- Manufacturing

facility

only

Network Flag

– For connection to Ethernet, select Hardware

and select the meter type, select Communications and
Connection/Network flag then Press New/Edit and enter the
Host and Port address.

The Host port address of the Ethernet module connected to the
meter would be typically 192.168.0.2:14001 (Contact your local
IT Department).

Elster Metering Ltd - M181 001 3C - 12/2007

Summary of Contents for A1120






























































































































































Search results

Summary of Contents for A1120

Reviews:

Related manuals for A1120

Brands by name

Popular brands

Elster A1120, User Manual

Search results

Summary of Contents for A1120

Reviews:

Related manuals for A1120

Brands by name

Popular brands