Elster A1120 User Manual Download Page 96

Page: 96 / 157

Power Master Unit

_________________________________________________________________

Read Me

If a new installation is being installed a Read Me screen is displayed.

Note

: The Read Me contains important information on the Master Unit installation.

Please familiarise yourself with the contents before proceeding with the installation.

Click Next to continue.

Type of Installation

The following types of installation can be
selected:

1. New

Installation

2. Upgrade PMU 16 bit -> PMU 32 bit

3. Upgrade PMU 32 bit -> later version 32 bit

Select your option and click Next to continue.

Note:

If New Installation is selected and a 16

or 32 bit version of the Master Unit is already
installed on your PC, a warning will be
displayed to select an upgrade option or
completely uninstall the Master Unit.

Choose Destination

The Power Master Unit will be installed in the
selected folder. The default destination is
C:\ELSTER\PMU\.

Use the Browse button to select another folder.

Click Next to continue.

A prompt is displayed if it is OK to overwrite the
installation. Click Yes.

Summary of Contents for A1120






























































































































































Search results

Summary of Contents for A1120

Reviews:

Related manuals for A1120

Brands by name

Popular brands

Elster A1120, User Manual

Search results

Summary of Contents for A1120

Reviews:

Related manuals for A1120

Brands by name

Popular brands