Elster A1120 User Manual Download Page 22 | Manualshive

Page: 22 / 157

background image

14

A1120/40 - Electronic Polyphase Meter

©

Elster Metering Limited - M181 001 2G - 5/2010

10.1.4 Customer Defined Registers

Two

C

ustomer

D

efined (CD) Registers are provided. These are cumulative registers which can

be used throughout the tariff scheme and load profile data and are programmable to accept
consumption from any two of the following like-unit registers:

kWh import

kWh export

Q1 kvarh

Q2 kvarh

Q3 kvarh

Q4 kvarh

kVAh 1

kVAh 2

Examples of their use are:

CD Register 1

Total kWh

kWh kWh export = Total kWh

CD Register 2

Total Import kvarh

Q1 + Q2 = Total Import kvarh

The contents of the Customer Defined Registers can be viewed on the display.

11 TARIFF

STRUCTURE

The tariff structure repeats year on year and comprises the following features:

8 Time-of-use (TOU) registers
4 Maximum demand registers
48 Switching times
12 Seasons
24 Change of season dates
32 Exclusion dates
13 End of billing dates

Daylight savings

Independent day control
Deferred tariff
Tariff scheme CRC

At least one Season must be programmed into the meter for TOU registers to be available.

«
...
20
21
22
23
24
...
»

Summary of Contents for A1120






























































































































































Reviews:

No comments

Related manuals for A1120

Brand: Landis+Gyr Pages: 10

Brand: Calsense Pages: 4

Brand: E+E Elektronik Pages: 40

Brand: ECO Sensors Pages: 22

Brand: ECO Sensors Pages: 7

Brand: F&F Pages: 24

Brand: Gardner Bender Pages: 7

Brand: National Instruments Pages: 15

Brand: Underground Magnetics Pages: 48

Brand: Pasco Scientific Pages: 11

Brand: AR Pages: 8

Sensorex SX41170SI

Brand: Meggitt Pages: 19

Speedrite Fault Finder

Brand: Tru-Test Pages: 2

Brand: PASCO Pages: 2

Analite NEP-5000

Brand: Observator Instruments Pages: 103

Brand: Young Pages: 5

SiteHawk SK-6000

Brand: BIRD Pages: 69

Brand: Proteus Pages: 4

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands