Elster A1120 User Manual Download Page 111

Page: 111 / 157

A1120/1140 Programmable Polyphase Meter Users Manual

___________________________________________________________________

Toolbar

The Scheme Toolbar is shown opposite. It consists
of the following components:

Restore Scheme

If a scheme has been modified but not saved, restore returns the scheme to its original settings.

Save Scheme

Save scheme saves the current scheme settings.

Quick Send

Quick send allows a scheme to be transferred to the meter.

Print

Sets up the properties for the system printer and allows all pages of the current scheme to be printed.

3.3

Starting a New Scheme

To enter a scheme from the Main Window, select File/New/A1120/40 scheme, or right click the mouse
in the right pane of the Scheme manager and select New/A1120/40 Scheme.

To Enter a Scheme -

In the Main Window, select the File/New/A1120/40 Scheme option.

A Scheme called New Scheme is entered in the Scheme manager and is highlighted.

Rename the scheme and press Enter.

3.4 Scheme

Editor

The Scheme Editor can be used to program all variants of the A1120/40 meter.

Elster Metering Ltd - M181 001 3C - 12/2007

Summary of Contents for A1120






























































































































































Search results

Summary of Contents for A1120

Reviews:

Related manuals for A1120

Brands by name

Popular brands

Elster A1120, User Manual

Search results

Summary of Contents for A1120

Reviews:

Related manuals for A1120

Brands by name

Popular brands