Elster A1120 User Manual Download Page 94 | Manualshive

Page: 94 / 157

background image

Power Master Unit

iii

_________________________________________________________________

Power Master Unit Meter Compatibility

Variants of the A1120/40 Meter that can be
programmed with the Power Master Unit are
shown opposite. This manual is for use with the
A1120 meter and the A1140 load profile meter
only.
See the list below for details of meter variants.

To program an A1700 (Vision) meter or PPM see
manual M120 001 6.

To program an A120 or A140 single phase meter,
see Manual M130 001 3.

For programming meters it is strongly
recommended that only one meter variant is
selected at a time.
If more than one type of meter is selected and a
Scheme is created, scheme parameters applicable
to the lowest specification of meter only will be
programmed to the meter.

A1120/40 Meter Variants

A1120/40 Versions

LM******** - A

Times always show UTC/GMT

LM******** - C

Times (as selected) show GMT/BST

LM*******B -

Import (Wh)

LM*******C -

Import (Wh), Q1 and Q4 (varh)

LM*******D -

Import (Wh), Q1 and Q4 (varh), VA 1

LM*******E -

Import/Export (Wh)

LM*******F -

Import/Export (Wh), Q1, Q2, Q3, Q4 (varh)

LM*******G -

Import/Export (Wh), VA 1/2

LM*******H -

Import/Export (Wh), Q1, Q2, Q3, Q4, (varh), VA 1/2

«
...
92
93
94
95
96
...
»

Summary of Contents for A1120






























































































































































Reviews:

No comments

Related manuals for A1120

Brand: KROHNE Pages: 34

Brand: VEE GEE Pages: 2

Brand: velocomp Pages: 4

Brand: Yamaha Pages: 98

Brand: SKF Pages: 12

Brand: DODODUCK Pages: 2

Brand: Spasciani Pages: 26

Brand: Guru Home Systems Pages: 20

sound SMART RLT Sport

Brand: VCA Pages: 36

Brand: dacell Pages: 39

Brand: Samick Pages: 48

Brand: Azbil Pages: 32

Brand: hager Pages: 4

Temp70 PT100 vio

Brand: XS Instruments Pages: 19

Brand: Elcometer Pages: 39

Brand: Velleman Pages: 13

APA ARIA Protection Adaptor

Brand: Ocean Reef Pages: 4

Brand: Parma Pages: 14

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands