Elster A1120 User Manual Download Page 130

Page: 130 / 157

Power Master Unit

___________________________________________________________________________

Meter Manager

5.1

Meter Manager Introduction

The Meter manager is used to organise the systems meter's. It is used to invoke the Meter
Information editor.

The Meter manager consists of three components.

Meters -

This is a list of meters available on the system. It allows Meter Connection information,

Identifiers and Security information to be configured.

To Enter a New Meter

Right click in the right hand pane of the Meter manager, select New Meter and rename the meter.

Import -

Schemes/meter that have been set up in other Master Units can be imported and placed in

the Schemes/meter Import folder.

Trash Can -

All files deleted from the Meter manager are transferred to the Trash Can.

They can be transferred back to the Meter manager if required. Once deleted from the Trash Can the
files are no longer available to the system.

Meter Manager Context Menu

Most of the features of the Context Menu are the same as the Scheme manager. The menu is made
available by right clicking the mouse in the right pane of the Meter manager.

Summary of Contents for A1120






























































































































































Search results

Summary of Contents for A1120

Reviews:

Related manuals for A1120

Brands by name

Popular brands

Elster A1120, User Manual

Search results

Summary of Contents for A1120

Reviews:

Related manuals for A1120

Brands by name

Popular brands