Elster A1120 User Manual Download Page 138

Page: 138 / 157

Power Master Unit

______________________________________________________________________________

File Locations

File location points the Master Unit to the location of externally produced files that may require
importing into the Master Unit. File types are shown in the left column and the setting (location) in
the right column.

To Modify a File Location, click on
Modify and select the directory where
the files of the selected type are located
then Press OK.

Meter Connection Setup

This dialog is used in exactly the same
way as the Connections Setup in the

Meter information editor

Communications Server Setup

The Communications Server Setup is used to assign the type of communication to be used on each
port and organise the Server File paths.

To enter the server setup, Select System/Communications Server Setup from the Scheme
manager Main menu.

Summary of Contents for A1120






























































































































































Search results

Summary of Contents for A1120

Reviews:

Related manuals for A1120

Brands by name

Popular brands

Elster A1120, User Manual

Search results

Summary of Contents for A1120

Reviews:

Related manuals for A1120

Brands by name

Popular brands