Elster A1120 User Manual Download Page 134 | Manualshive

Page: 134 / 157

background image

Power Master Unit

35

___________________________________________________________________________

Meter List

6.1

The Meter List Components

The Meter list consists of a list of meters with their associated Schemes brings
together meters configured in the Meter manager, and Schemes created in the
Scheme manager, to create a list of meters and their associated schemes.

This is achieved by copying a Meter and a Scheme into the Meter list.

Note 1:

If a Scheme is incompatible with a meter, warning triangles appear as

shown opposite. Right click on the meter or scheme and select Show Conflicts
to establish the reason.

Note 2

: Multiple schemes can be sent to a meter as a single communications

session by attaching the schemes to the meter using drag and drop. It should be noted that if the
same scheme page (e.g. display page) is contained in more than one of the schemes, only the page
from the last scheme attached is programmed to the meter.

Meter List Context Menu

The options available from the dropdown list are shown opposite.
The Context Menu list is made available by right clicking the mouse in the
right pane of the Meter list.

New Meter List

The New option clears the Meter list ready for a new Meter list to be created.

Open Scheme -

This allows information on the meter or meter scheme to be viewed or edited using

Save. A new Meter List can also be created by editing the Meter List and Using the Save As facility.

Remove -

Removes the selected list from the Meter List

Show Conflicts -

Shows any discrepancies between the scheme and the meter

New Meter List

- Allows a new Meter list to be created

Open Meter List -

Allows a selected Meter list to be opened

Save Meter List -

Allows the current Meter list to be Saved

Save Meter List As

- Allows the selected Meter list to be saved as a new name

Execute Meter List -

Execute

Meter List is used for communicating with a meter.

It is used with the Meter Communications Server to Program or Read.

«
...
132
133
134
135
136
...
»

Summary of Contents for A1120






























































































































































Reviews:

No comments

Related manuals for A1120

Brand: Bacharach Pages: 87

Brand: R.M. Young Pages: 2

Brand: Facom Pages: 42

Brand: jablotron Pages: 2

Brand: WATERGUARD Pages: 2

Brand: Velleman Pages: 107

Brand: BYOGuitar.com Pages: 11

Brand: Siko Pages: 2

Brand: Sensia Pages: 139

Brand: York Pages: 2

Brand: Keller Pages: 4

Brand: Rodstation Pages: 28

QI-POWER-485-300

Brand: QEED Pages: 2

Brand: Feature tech Pages: 2

iNELS Air AirCFS-100S

Brand: Elko Pages: 4

Brand: PCE Health and Fitness Pages: 7

Brand: Hanna Instruments Pages: 2

American AL-1000

Brand: Badger Meter Pages: 16

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands