Elster A1120 User Manual Download Page 131

Page: 131 / 157

A1120/1140 Programmable Polyphase Meter Users Manual

___________________________________________________________________

Meter Information Editor

This Editor is used to reference data related to a specific meter and its location, the type of
communications and security information. To open the Information Editor, double click on a meter.

The dialog is divided into three Tabs, Communications, Hardware and Identifiers.

Hardware

Information on the Meter type, Connection type, number of elements, Number of internal relays and
Plug in modules is entered (see above).

Communications

This page allows the Communications parameters to be entered.

To Enter Communications Parameters

Enter the connection method and any outstation no., telephone no., baud rate as required

Note:- If a suitable Connection method already exists, it can be selected from the Connection List.

For new connections refer to Section 8.1

Elster Metering Ltd - M181 001 3C - 12/2007

Summary of Contents for A1120






























































































































































Search results

Summary of Contents for A1120

Reviews:

Related manuals for A1120

Brands by name

Popular brands

Elster A1120, User Manual

Search results

Summary of Contents for A1120

Reviews:

Related manuals for A1120

Brands by name

Popular brands