Elster A1120 User Manual Download Page 154

Page: 154 / 157

Power Master Unit

______________________________________________________________________________

Date of Expiry -

This is the date of expiry of the current CHIRPS Configuration File. A new file with

the following format must be loaded.

Day of Month

( 2 Characters)

01-31

Month

(

Characters)

01-12

Last 2 digits of Year

( 2 Characters)

00-99

Number of Sessions -

This is the number of sessions that CHIRPS will run in the range of 0000 to

9999. After entry the value decrements by one until it reaches 0001. CHIRPS will then cease to run.

If the number is initially set to zero, CHIRPS will run for an indefinite number of times.

HHU Identification -

This is an eight digit identifier determining the type of HHU that CHIRPS is

running on.

File Size -

The file size should always be set to 12

Comms Port -

If the first three characters are set to COM. then the fourth character is interpreted as

the comms port (e.g. COM1) which is the default value.

Timings -

CHIRPS timing protocols should be set to the following values and not changed.

Timing 1

1600

Timing 2

3000

Timing 3

0200

Timing 4

0100

Load Default -

The default file is identical to the Configuration File and can be loaded in case

CHIRPS has been corrupted.

A new default file can be generated by saving the data and re-saving the file HHU.CFG to HHU.DEF.

Click System Exit to return to the Power Master Unit.

Summary of Contents for A1120






























































































































































Search results

Summary of Contents for A1120

Reviews:

Related manuals for A1120

Brands by name

Popular brands

Elster A1120, User Manual

Search results

Summary of Contents for A1120

Reviews:

Related manuals for A1120

Brands by name

Popular brands