manualshive.com logo in svg

Ekolot KR-030 TOPAZ, Handling, Maintenance And Periodic Inspections Manual, Page: 90 / 189

Share
Download
Ekolot KR-030 TOPAZ Handling, Maintenance And Periodic Inspections Manual Download Page 90

Manufacturer: PPHU 
EKOLOT 
Type: KR-030 TOPAZ

 

Handling, Maintenance and Periodic Inspections  

Manual

 

 

Issue: 1 
Rev. N

o

: 

Date: July 2010 
Date:  

Page 
90 

 

 

 

 
4.  Pull out the cable J.12.450.00.03 from the Bowden conduit. 
5.  Loosen the bolts M5x5 in the cables clamps J.12.412.05.03 in the 

intermediate brackets and in the levers (Pic. 9.4.2.1 & 9.4.2.4).  

6.  In the intermediate bracket (Pic. 9.4.3) loosen the tension 

regulatorJ.12.423.05.03 so the Bowden conduit could be pulled out 
from the seats. 

7.  Install the bolt M5x10 (Pic. 9.4.2.1) and remove the lever arms (left 

and right). 

8.  Remove the cables from the lever arms and the intermediate 

brackets. 

9.  Undo the nut (Pic. 9.4.3 white arrow with „N” description) and remove 

the bracket J.12.422.00.03 from the axle J.12.423.00.03 (Pic. 
9.4.2.4). 

10.  Take out the cable tips from the catches in the bracket 

J.12.422.00.03. 

 

9.4.2.3  Installation of throttle control in the cockpit 

Install the throttle lever brackets J.12.411.00.03  and the 
intermediate body bracket J.12.423.00.03 on the fuselage 
structure. 
 

J.12.450.00.03 

Bolt M4x12 DIN 7985 
Washer 

Ø

4 DIN 1440 

Nut M4 DIN 985

 

 

Pic. 9.4.2.7 

J.12.412.05.03 
Bolt M5x5 DIN 913

 

Summary of Contents for KR-030 TOPAZ






























































































































































































Reviews:

No comments