Ekolot KR-030 TOPAZ Handling, Maintenance And Periodic Inspections Manual Download

Page: 104 / 189

Manufacturer: PPHU
EKOLOT
Type: KR-030 TOPAZ

Handling, maintenance and periodic inspections

manual

Issue: 1
Rev. N

Date: July 2010
Date:

Page
104

−

Loosen the clamp on the fuel pipe J.15.400.08.00 and remove the

pipe from the barb fitting

−

Remove the drain valve (see the point 6 below)

−

Using a wrench 20 mm remove the nut (J.15.430.08.00) that fixes

the sediment bowl to the fuselage structure

−

Remove the sediment tank from the fuselage

Fuel pipe

J.15.400.08.00

Clamp W1

13-15

J.15.430.00.01

Fuselage

belly

J.15.430.08.00

Pic. 9.4.3.19

Pic. 9.4.3.20

Summary of Contents for KR-030 TOPAZ






























































































































































































Search results

Summary of Contents for KR-030 TOPAZ

Reviews:

Related manuals for KR-030 TOPAZ

Brands by name

Popular brands

Ekolot KR-030 TOPAZ, Handling, Maintenance And Periodic Inspections Manual

Search results

Summary of Contents for KR-030 TOPAZ

Reviews:

Related manuals for KR-030 TOPAZ

Brands by name

Popular brands