Ekolot KR-030 TOPAZ Handling, Maintenance And Periodic Inspections Manual Download Page 22 | Manualshive

Page: 22 / 189

Ekolot KR-030 TOPAZ Handling, Maintenance And Periodic Inspections Manual Download Page 22

Manufacturer: PPHU
EKOLOT
Type: KR-030 TOPAZ

Handling, Maintenance and Periodic Inspections

Manual

Issue: 1
Rev. N

o

:

Date: July 2010
Date:

Page
22

9.1.9 Wheel removal

1.  Unscrew the valve and release air from the inner tube.
2.  Remove the 6 bolts that attach the rim to the hub.
3.  Remove the rim and the tyre

9.1.10 Removal of the front undercarriage pole

1. Unscrew the bolt

Mx10, 8,8 DIN 912 (Pic. 9.1.7 at the page 18)

2.  Start the clamp bolt (Pic. 9.1.7 at the page 17)
3.  Move the lever J.13.122.00.01 from the pole J.13.200.00.04 upward.
4.  Remove the pole from the fuselage bushing.

9.1.11 Installation of the front undercarriage

1. After reassembly the front undercarriage (Pic. 9.1.6 page 17), install the

fairing and fix it to the fork with the bolts (Pic. on the page18)

2. Lubricate top of the pole and slide it into the bushing in the fuselage.
3. Install the control lever J.13.122.00.01 (Pic. 9.1.7, page 17) with the bar

assembled J.12.622.00.00 (Pic. 9.1.7, page18)

Pic. 9.1.15

«
...
20
21
22
23
24
...
»

Summary of Contents for KR-030 TOPAZ






























































































































































































Reviews:

No comments