Eaton IQ 250, User & Installation Manual

Page: 122 / 142

A
IQ 250/260 Meter Appendix B:
Modbus Mapping
conditional write
5207 - 5207 21000 - 21000 Initiate Meter Firmware Reprogramming UINT16 password5 1
5208 - 5208 21001 - 21001 Force Meter Restart UINT16 password5 Causes a watchdog reset, always reads 0. 1
5209 - 5209 21002 - 21002 Open Privileged Command Session UINT16 password5 Meter will process command registers (this register through
'Close Privileged Command Session' register below) for 5
minutes or until the session is closed, whichever comes
first. 1
520A - 520A 21003 - 21003 Initiate Programmable Settings Update UINT16 password5 Meter enters PS update mode. 1
520B - 520B 21004 - 21004 Calculate Programmable Settings Checksum3 UINT16 0000 to 9999 Meter calculates checksum on RAM copy of PS block. 1
520C - 520C 21005 - 21005 Programmable Settings Checksum3 UINT16 0000 to 9999 Read/write checksum register; PS block saved in
nonvolatile memory on write
8
.
1
520D - 520D 21006 - 21006 Write New Password3 UINT16 0000 to 9999 Write-only register; always reads zero. 1
520E - 520E 21007 - 21007 Terminate Programmable Settings Update3 UINT16 any value Meter leaves PS update mode via reset. 1
520F - 5211 21008 - 21010 Set Meter Clock TSTAMP 1Jan2000 - 31Dec2099 1 sec Saved only when 3rd register is written. 3
5212 - 5212 21011 - 21011 Reserved Set to 0. 1
5213 - 5219 21012 - 21018 Reserved Set to 0. 7
521A - 521A 21019 - 21019 Close Privileged Command Session UINT16 any value Ends an open command session. 1
Block Size: 20
read/write
658F - 659A 26000 - 26011 Perform a Secure Operation UINT16 Encrypted command to read password or change meter
type. 12
Block Size: 12
write only in PS update mode
752F - 752F 30000 - 30000 CT multiplier & denominator UINT16 bit-mapped
dddddddd mmmmmmmm
High byte is denominator (1 or 5, read-only),
low byte is multiplier (1, 10, or 100). 1
7530 - 7530 30001 - 30001 CT numerator UINT16 1 to 9999 none 1
7531 - 7531 30002 - 30002 PT numerator UINT16 1 to 9999 none 1
7532 - 7532 30003 - 30003 PT denominator UINT16 1 to 9999 none 1
7533 - 7533 30004 - 30004 PT multiplier & hookup UINT16 bit-mapped mmmmmmmm mmmmhhhh mm…mm = PT multiplier (1, 10, 100, or 1000)
hhhh = hookup enumeration (0 = 3 element wye[9S], 1 =
delta 2 CTs[5S], 3 = 2.5 element wye[6S]) 1
7534 - 7534 30005 - 30005 Averaging Method UINT16 bit-mapped --iiiiii b----sss iiiiii = interval (5,15,30,60)
b = 0-block or 1-rolling
sss = # subintervals (1,2,3,4) 1
7535 - 7535 30006 - 30006 Power & Energy Format UINT16 bit-mapped pppp--nn -eee-ddd pppp = power scale (0-unit, 3-kilo, 6-mega, 8-auto)
nn = number of energy digits (5-8 --> 0-3)
eee = energy scale (0-unit, 3-kilo, 6-mega)
ddd = energy digits after decimal point (0-6)
See note 10. 1
Encryption Block
Programmable Settings Section
Basic Setups Block
Privileged Commands Block
www.eaton.com IB02601006E MM-16