Eaton IQ 250, User & Installation Manual

Page: 110 / 142

A
IQ 250/260 Meter Appendix B:
Modbus Mapping
read-only
1003 - 1003 4100 - 4100 Phase A Current SINT16 -1800 to +1800 0.1 degree 1
1004 - 1004 4101 - 4101 Phase B Current SINT16 -1800 to +1800 0.1 degree 1
1005 - 1005 4102 - 4102 Phase C Current SINT16 -1800 to +1800 0.1 degree 1
1006 - 1006 4103 - 4103 Angle, Volts A-B SINT16 -1800 to +1800 0.1 degree 1
1007 - 1007 4104 - 4104 Angle, Volts B-C SINT16 -1800 to +1800 0.1 degree 1
1008 - 1008 4105 - 4105 Angle, Volts C-A SINT16 -1800 to +1800 0.1 degree 1
Block Size: 6
read-only
1193 - 1193 4500 - 4500 Port ID UINT16 1 to 4 none Identifies which IQ 250/260 COM port a master is
connected to: 2 for COM2, etc. See chapter 5 for COM port
assignments. 1
1194 - 1194 4501 - 4501 Meter Status UINT16 bit-mapped
mmmpch-- -ffeeccc
mmm = measurement state (0=off, 1=running normally,
2=limp mode, 3=warmup, 6&7=boot, others unused) See
note 16.
pch = NVMEM block OK flags (p=profile, c=calibration,
h=header), flag is 1 if OK
ff = flash state (0=initializing, 1=logging disabled by Vswitch,
3=logging)
ee = edit state (0=startup, 1=normal, 2=privileged
command session, 3=profile update mode)
ccc = port enabled for edit(0=none, 1-4=COM1-COM4,
7=front panel) 1
1195 - 1195 4502 - 4502 Limits Status UINT16 bit-mapped 87654321 87654321 High byte is setpt 1, 0=in, 1=out
low byte is setpt 2, 0=in, 1=out
see notes 11, 12, 17 1
1196 - 1197 4503 - 4504 Time Since Reset UINT32 0 to 4294967294 4 msec Wraps around after max count. 2
1198 - 119A 4505 - 4507 Meter On Time TSTAMP 1Jan2000 - 31Dec2099 1 sec 3
119B - 119D 4508 - 4510 Current Date and Time TSTAMP 1Jan2000 - 31Dec2099 1 sec 3
119E - 119E 4511 - 4511 Reserved Reserved 1
119F - 119F 4512 - 4512 Current Day of Week UINT16 1 to 7
1 day
1=Sun, 2=Mon, etc. 1
Block Size: 13
read-only
176F - 176F 6000 - 6000 Volts A-N, %THD UINT16 0 to 10000 0.01% 1
1770 - 1770 6001 - 6001 Volts B-N, %THD UINT16 0 to 10000 0.01% 1
1771 - 1771 6002 - 6002 Volts C-N, %THD UINT16 0 to 10000 0.01% 1
1772 - 1772 6003 - 6003 Amps A, %THD UINT16 0 to 10000 0.01% 1
1773 - 1773 6004 - 6004 Amps B, %THD UINT16 0 to 10000 0.01% 1
1774 - 1774 6005 - 6005 Amps C, %THD UINT16 0 to 10000 0.01% 1
1775 - 179C 6006 - 6045 Phase A Voltage harmonic magnitudes UINT16 0 to 10000 0.01% 40
179D - 17C4 6046 - 6085 Phase A Voltage harmonic phases SINT16 -1800 to +1800 0.1 degree 40
17C5 - 17EC 6086 - 6125 Phase A Current harmonic magnitudes UINT16 0 to 10000 0.01% 40
17ED - 1814 6126 - 6165 Phase A Current harmonic phases SINT16 -1800 to +1800 0.1 degree 40
1815 - 183C 6166 - 6205 Phase B Voltage harmonic magnitudes UINT16 0 to 10000 0.01% 40
183D - 1864 6206 - 6245 Phase B Voltage harmonic phases SINT16 -1800 to +1800 0.1 degree 40
1865 - 188C 6246 - 6285 Phase B Current harmonic magnitudes UINT16 0 to 10000 0.01% 40
188D - 18B4 6286 - 6325 Phase B Current harmonic phases SINT16 -1800 to +1800 0.1 degree 40
18B5 - 18DC 6326 - 6365 Phase C Voltage harmonic magnitudes UINT16 0 to 10000 0.01% 40
In each group of 40 registers, the first register represents
the fundamental frequency or first harmonic, the second
represents the second harmonic, and so on up to the 40th
register which represents the 40th harmonic.
Harmonic magnitudes are given as % of the fundamental
magnitude. Thus the first register in each group of 40 will
typically be 9999. A reading of 10000 indicates invalid.
Phase Angle Block
Status Block
THD Block13
www.eaton.com IB02601006E MM-4