Installation Instructions for Wi-Q™ Technology 9KQ Cylindrical Locks
14
Completing the installation
BEST
a Product Group of dormakaba USA Inc.
Figure 20b Installing the top cover
20
Install top cover
(inside escutcheon)
1 Connect the antenna to its mating connector.
2 Place the top cover against the door and above the fire
plate. Slide the top cover down toward the bottom
cover as shown in Figure 20b.
Caution:
As you slide the top cover onto the fire
plate, feed the antenna wire down into the
bottom cover. Be sure not to pinch the antenna
wire on the bottom cover as you slide the top
cover into place.
3 Use two cover screws to secure the cover to the side of
the fire plate, as shown in Figure 20b.
Note: Phillips Type 2 and T20 Torx options are available
for the cover mounting screws.
Figure 20a Inside view of top cover
Top cover
Antenna wire
Top cover
Inside of door
Cover screws
Antenna wire
BEST
a Product Group of dormakaba USA Inc.
Installation Instructions for Wi-Q™ Technology 9KQ Cylindrical Locks
Completing the installation
IE]
Install inside and outside levers
Note: To use a core and throw member from a manu
facturer other than BEST with a Electronic Stand-a/one
Lock, see the
Installation Instructions for 9K Non-inter
changeable Cores & Throw Members
(T56093) and
skip task 79.
■ With the handle pointing toward the door hinges,
position a lever on the outside sleeve and push firmly
on the lever until it is seated. Repeat, placing the other
lever on the inside sleeve.
[El
Install core and throw member
1.
For 6-pin core users only:
Install the plastic spacer
(not shown, supplied with permanent cores) on the
throw member.
2. Insert the control key into the core and rotate the
key 15 degrees to the right.
3. Insert the throw member into the core.
4. Insert the core and throw member into the lever
with the control key while keeping the throw member
in line with the cam inside the lever.
Caution:
The control key can be used to remove
cores and to access doors. Provide adequate
security for the control key.
Outside of door
Figure 78 Installing the levers
/Core
Figure 19a Installing the throw member.
Figure 7 9b Installing the core
13
Installation Instructions for Wi-Q™ Technology 9KQ Cylindrical Locks
Completing the installation
IE]
Install inside and outside levers
Note: To use a core and throw member from a manu
facturer other than BEST with a Electronic Stand-a/one
Lock, see the
Installation Instructions for 9K Non-inter
changeable Cores & Throw Members
(T56093) and
skip task 79.
■ With the handle pointing toward the door hinges,
position a lever on the outside sleeve and push firmly
on the lever until it is seated. Repeat, placing the other
lever on the inside sleeve.
[El
Install core and throw member
1.
For 6-pin core users only:
Install the plastic spacer
(not shown, supplied with permanent cores) on the
throw member.
2. Insert the control key into the core and rotate the
key 15 degrees to the right.
3. Insert the throw member into the core.
4. Insert the core and throw member into the lever
with the control key while keeping the throw member
in line with the cam inside the lever.
Caution:
The control key can be used to remove
cores and to access doors. Provide adequate
security for the control key.
Outside of door
Figure 78 Installing the levers
/Core
Figure 19a Installing the throw member.
Figure 7 9b Installing the core
13
Summary of Contents for BEST Wi-Q ONGUARD
