DirecTV Advanced Installation Meter 2 Operation Manual Download Page 64

Page: 64 / 108

Page 64

AIM 2 Operation Manual

7. On the

EIV RESULTS

screen, review the

results for all supported orbital slots and

SWiM

channels (if applicable). A satisfactory result

is indicated by a checkmark. A problem is

indicated by an X. An inconclusive result is

indicated by a dash.
If a checkmark appears for all supported orbital

slots, the ODU alignment is acceptable.
If an X appears for an orbital slot, perform the

following steps:

• Press

REPEAT EIV

to confirm the

problem.

• If an X appears again for one or

more orbital slots, you can press

EIV

DETAIL

to determine which tests failed.

Troubleshoot any failures following the

instructions provided by DIRECTV.

To change the location where you are testing,

press

CHANGE LOC

On the EIV DETAILS screen, you can press NEXT to view the

details for another orbital slot, or press BACK to scroll back

through the details to the EIV RESULTS screen.

You also can press NOTES to add a note about the EIV.

Summary of Contents for Advanced Installation Meter 2













































































































Search results

Summary of Contents for Advanced Installation Meter 2

Reviews:

Related manuals for Advanced Installation Meter 2

Brands by name

Popular brands

DirecTV Advanced Installation Meter 2, Operation Manual

Search results

Summary of Contents for Advanced Installation Meter 2

Reviews:

Related manuals for Advanced Installation Meter 2

Brands by name

Popular brands