DirecTV Advanced Installation Meter 2 Operation Manual Download Page 23

Page: 23 / 108

Page 23

AIM 2 Operation Manual

Connect the battery connector into the slot at the bottom right of the cavity (the slot

is keyed to only accept proper insertion).

6. Insert the battery so that the cable is in the bottom left

corner, as shown here. Place the upper right corner

of the battery into the cavity first, so that the foam is

compressed to allow the pack to fit snugly.

7. Push the wire cable down into the pathway. Then insert

the bottom of the battery door into the slots at the

bottom of the cavity.

8. Tilt the battery door back into place and tighten the 2

screws with a Phillipshead screwdriver.

To confirm that the battery has been installed correctly, press and hold the Power

button to make sure that the AIM turns on.

10. Follow local guidelines for battery disposal.

Wire cable

After replacing a battery, the displayed battery level may

not represent the actual battery life until the battery is fully

recharged.

Summary of Contents for Advanced Installation Meter 2













































































































Search results

Summary of Contents for Advanced Installation Meter 2

Reviews:

Related manuals for Advanced Installation Meter 2

Brands by name

Popular brands

DirecTV Advanced Installation Meter 2, Operation Manual

Search results

Summary of Contents for Advanced Installation Meter 2

Reviews:

Related manuals for Advanced Installation Meter 2

Brands by name

Popular brands