DirecTV Advanced Installation Meter 2 Operation Manual Download Page 70

Page: 70 / 108

Page 70

AIM 2 Operation Manual

Connect the AIM ODU F connector at the

location in the distribution network indicated on

the display. Then press

RUN TEST

and wait for

the results.

7. On the

GUIDED RESULTS

screen, review the

results of the EIV Plus. Then do one of the

following:

• To view detailed results, press

DETAILS

to go to the

GUIDED DETAILS

screen.

Go to Step 8.

• To repeat EIV Plus at the same location,

press

REPEAT TEST

and wait for the

results of the test.

• If results indicate a problem with the

ODU alignment, press

REPOINT

to go

to the

PRE CONFIGURE ODU

screen.

Then follow the instructions in

Chapter 6

to align the ODU.

• To continue troubleshooting, press

NEXT

to go to the

GUIDED LOCATION

screen

and perform EIV Plus at a new location. Repeat Step 6.

•

When all problems have been addressed and troubleshooting is complete, you

can press

DONE

to return to the

TEST

screen.

If it is raining and an attempt to realign the ODU fails, you can

enable Rain Mode to account for environmental conditions

and continue troubleshooting.

Press Fn and then 4 to enable Rain Mode. Press Repeat

Test and wait for the results of the test. The Rain Mode icon

appears on the Results screen to indicate the test was run

in Rain Mode. If the test fails again, the failure may be due to

signal degradation from the rain, or there may an issue with

the LNB.

Summary of Contents for Advanced Installation Meter 2













































































































Search results

Summary of Contents for Advanced Installation Meter 2

Reviews:

Related manuals for Advanced Installation Meter 2

Brands by name

Popular brands

DirecTV Advanced Installation Meter 2, Operation Manual

Search results

Summary of Contents for Advanced Installation Meter 2

Reviews:

Related manuals for Advanced Installation Meter 2

Brands by name

Popular brands