DirecTV Advanced Installation Meter 2 Operation Manual Download Page 80

Page: 80 / 108

Page 80

AIM 2 Operation Manual

12. On the

SAT TUNE RESULTS

screen, review

the results of the test. The screen shows:

• Power

of the transponder signal (in

dBm—power ratio in decibels of the

measured power referenced to one

milliwatt).

• Measurement of the signal-to-noise ratio,

expressed as

SNR

in decibels.

• Measurement of the signal quality,

expressed as an

value between

and 100.

• Frequency

offset

of the transponder signal from its expected frequency (in

megahertz).

• Indication as to whether the transponder signal is above the power

lock

threshold.

13.

Troubleshoot any problems following the instructions provided by DIRECTV.

• To repeat the test at a different location, press

CHANGE LOC

. Then go to Step

• To repeat the test at a different orbital slot, press

CHANGE SAT

. Then go to Step

• To repeat the test at a different transponder, press

CHANGE TR

Then go to Step

10.
To repeat the test for a sequential transponder, use the up/down arrow buttons

to change the transponder number to the next or previous transponder. The SAT

TUNE RESULTS

screen updates to show the results of the test for the selected

transponder.

14. Press DONE to return to the TEST screen.

Summary of Contents for Advanced Installation Meter 2













































































































Search results

Summary of Contents for Advanced Installation Meter 2

Reviews:

Related manuals for Advanced Installation Meter 2

Brands by name

Popular brands

DirecTV Advanced Installation Meter 2, Operation Manual

Search results

Summary of Contents for Advanced Installation Meter 2

Reviews:

Related manuals for Advanced Installation Meter 2

Brands by name

Popular brands