DirecTV Advanced Installation Meter 2 Operation Manual Download Page 71

Page: 71 / 108

Page 71

AIM 2 Operation Manual

8. On the

GUIDED DETAILS

screen, review the

possible problems with the installation. Then do

one of the following:

• To view results of the EIV Plus, press

EIV PLUS RESULTS

to go to the

GUIDED EIV PLUS RESULTS

screen.

Go to Step 9.

• To view cumulative results for all EIV

Plus tests performed in Guided Mode

for the installation, press

VIEW DATA

go to the

GUIDED DATA

screen. Go to

Step 10.

• To continue troubleshooting, press

DONE

to go back to the

GUIDED

RESULTS

screen. Go back to Step 7.

9. On the

GUIDED EIV PLUS RESULTS

screen,

review the results for all supported orbital

slots and SWiM channels (if applicable). A

satisfactory result is indicated by a checkmark.

A problem is indicated by an X. An inconclusive

result is indicated by a dash.

• If an X appears for one or more orbital

slots, you can press

EIV PLUS DETAIL

to determine which tests failed. Then

press

NEXT

to view the details for

another orbital slot, or press

BACK

scroll back through the details to the

GUIDED EIV PLUS RESULTS

screen.

•

When you have finished reviewing EIV

Plus results on the

GUIDED EIV PLUS

RESULTS

screen, you can press

DONE

to return to the

GUIDED DETAILS

screen.

Summary of Contents for Advanced Installation Meter 2













































































































Search results

Summary of Contents for Advanced Installation Meter 2

Reviews:

Related manuals for Advanced Installation Meter 2

Brands by name

Popular brands

DirecTV Advanced Installation Meter 2, Operation Manual

Search results

Summary of Contents for Advanced Installation Meter 2

Reviews:

Related manuals for Advanced Installation Meter 2

Brands by name

Popular brands