DirecTV Advanced Installation Meter 2 Operation Manual Download Page 37

Page: 37 / 108

Page 37

AIM 2 Operation Manual

IP Address

Once

IP Settings

is set to

Manual

, you can set

each of the network IP address values.

1. Select

Address

and press

SELECT

to go to

the

ADDRESS

screen.

2. Enter the IP address and press

SELECT

• To delete a character, press the

Back

button. You also can use left/right arrow

buttons to navigate within your entry, or

press

CLEAR

to delete the entry and start

over. Press

CANCEL

to exit without saving

changes.

3. Press

ENTER

to save and return to the

ETHERNET SETTINGS

screen.

Gateway, Netmask, and DNS Addresses

Select each of the other IP settings as necessary and modify using the steps above.

Summary of Contents for Advanced Installation Meter 2













































































































Search results

Summary of Contents for Advanced Installation Meter 2

Reviews:

Related manuals for Advanced Installation Meter 2

Brands by name

Popular brands

DirecTV Advanced Installation Meter 2, Operation Manual

Search results

Summary of Contents for Advanced Installation Meter 2

Reviews:

Related manuals for Advanced Installation Meter 2

Brands by name

Popular brands