DirecTV Advanced Installation Meter 2 Operation Manual Download Page 77

Page: 77 / 108

Page 77

AIM 2 Operation Manual

If it is raining and an attempt to realign the ODU fails, you can

enable Rain Mode to account for environmental conditions

and continue troubleshooting.

Press Fn and then 4 to enable Rain Mode. Press Repeat

Test and wait for the results of the test. The Rain Mode icon

appears on the Results screen to indicate the test was run

in Rain Mode. If the test fails again, the failure may be due to

signal degradation from the rain, or there may an issue with

the LNB.

When you have finished reviewing EIV Plus

results on the EIV PLUS RESULTS screen, you

can press DONE to return to the HOME screen.

You also can press CHANGE LOC to perform

EIV Plus for another location.

On the EIV PLUS DETAILS screen, you can press NEXT to

view the details for another orbital slot, or press BACK to

scroll back through the details to the EIV PLUS RESULTS

screen.

You also can press NOTES to add a note about the EIV Plus.

Summary of Contents for Advanced Installation Meter 2













































































































Search results

Summary of Contents for Advanced Installation Meter 2

Reviews:

Related manuals for Advanced Installation Meter 2

Brands by name

Popular brands

DirecTV Advanced Installation Meter 2, Operation Manual

Search results

Summary of Contents for Advanced Installation Meter 2

Reviews:

Related manuals for Advanced Installation Meter 2

Brands by name

Popular brands