DirecTV Advanced Installation Meter 2 Operation Manual Download Page 4

Page: 4 / 108

Page 4

AIM 2 Operation Manual

Chapter 4 ............................................................................................................27

Setting Up the Meter ...............................................................................................................27

Overview ..............................................................................................................................27

Entering Registration Information.........................................................................................28

Setting up the Wi-Fi Connection ..........................................................................................30

Setting up the Bluetooth Connection....................................................................................32

Setting up the Ethernet Connection .....................................................................................35

IP Settings ......................................................................................................................36

IP Address ......................................................................................................................37

Gateway, Netmask, and DNS Addresses .......................................................................37

Changing the Volume Settings .............................................................................................38

Changing the Display Contrast or Brightness ......................................................................39

Changing the Time and Date Settings .................................................................................40

Changing the Automatic Timer Settings ...............................................................................42

Chapter 5 ............................................................................................................45

Setting Up a Job ......................................................................................................................45

Overview ..............................................................................................................................45

Starting a Job .......................................................................................................................46

Modifying the Setup for a Job ..............................................................................................47

Notes ..............................................................................................................................47

Dish Type ........................................................................................................................48

Reverse / International LNB............................................................................................48

Switch Type ....................................................................................................................49

Zip Code

.........................................................................................................................49

Chapter 6 ............................................................................................................51

Installing an ODU .....................................................................................................................51

Overview ..............................................................................................................................51

Aligning the ODU ............................................................................................................51

ODU Installation Tasks ...................................................................................................52

Task A. Installation Setup................................................................................................53

Task B. Coarse Azimuth Adjustment

...............................................................................54

Task C. Coarse Elevation Adjustment

.............................................................................54

Task D. Tilt Adjustment (95°, 3-LNB, Slimline-5, and Slimline-5S (SWiM) ODUs Only)

.55

Task E. Fine Elevation Adjustment (Slimline ODUs Only)

..............................................55

Task F. Fine Azimuth Adjustment (Slimline ODUs Only)

.................................................57

Performing EIV Following ODU Installation ....................................................................58

Summary of Contents for Advanced Installation Meter 2













































































































Search results

Summary of Contents for Advanced Installation Meter 2

Reviews:

Related manuals for Advanced Installation Meter 2

Brands by name

Popular brands

DirecTV Advanced Installation Meter 2, Operation Manual

Search results

Summary of Contents for Advanced Installation Meter 2

Reviews:

Related manuals for Advanced Installation Meter 2

Brands by name

Popular brands