DirecTV Advanced Installation Meter 2 Operation Manual Download Page 102

Page: 102 / 108

Page 102

AIM 2 Operation Manual

6. To transfer all records for an account, do

the following on the

VIEW RECORDS BY

ACCOUN

T screen:

• Highlight the account number and

press

OPTIONS

• On the

Options

window, highlight

Copy...

Move...

and press

• Highlight the type of records to

transfer and press

. You can

select

Copy All Records

Move

All Records

to transfer all records for

the account, or select a specific type

of records to transfer.

• Go to Step 7.

On the message that appears to confirm the

transfer, press

The records are transferred, and the

RECORDS MAIN, VIEW RECORDS

, or

VIEW RECORDS BY ACCOUNT

screen

appears.

Summary of Contents for Advanced Installation Meter 2













































































































Search results

Summary of Contents for Advanced Installation Meter 2

Reviews:

Related manuals for Advanced Installation Meter 2

Brands by name

Popular brands

DirecTV Advanced Installation Meter 2, Operation Manual

Search results

Summary of Contents for Advanced Installation Meter 2

Reviews:

Related manuals for Advanced Installation Meter 2

Brands by name

Popular brands