DirecTV Advanced Installation Meter 2 Operation Manual Download Page 76

Page: 76 / 108

Page 76

AIM 2 Operation Manual

7. On the

EIV PLUS TEST

screen, you can do

one of the following:

• To select an individual polarity for the

EIV Plus, press

OPTIONS

. On the

EIV

PLUS OPTIONS

screen, highlight the

polarity for the EIV Plus.Then press

SELECT

to continue.

• To select the channel for an installation

with a DSWiM-13 where the test

location

is between the DSWiM and IRD, press

OPTIONS

. On the

EIV PLUS OPTIONS

screen, press

SELECT

. Then highlight

the DSWiM channel and press

SELECT

• To add a note about the EIV Plus, such

as details about where the EIV Plus is

being performed, press

NOTES

. Then

enter the note.

• To run the test, press

RUN EIV PLUS

and wait briefly for the results.

8. On the

EIV PLUS RESULTS

screen, review the

results for all supported orbital slots and SWiM channels (if applicable). A satisfactory

result is indicated by a checkmark. A problem is indicated by an X. An inconclusive

result is indicated by a dash.

• If a checkmark appears for all supported orbital slots, the ODU alignment is

acceptable.

• If an X appears for an orbital slot, perform the following steps:

• Press

REPEAT EIV PLUS

to confirm the problem.

• If X appears again for one or more orbital slots, you can press

EIV

PLUS DETAIL

to determine which tests failed. Troubleshoot any failures

following the instructions provided by DIRECTV.

Summary of Contents for Advanced Installation Meter 2













































































































Search results

Summary of Contents for Advanced Installation Meter 2

Reviews:

Related manuals for Advanced Installation Meter 2

Brands by name

Popular brands

DirecTV Advanced Installation Meter 2, Operation Manual

Search results

Summary of Contents for Advanced Installation Meter 2

Reviews:

Related manuals for Advanced Installation Meter 2

Brands by name

Popular brands