DirecTV Advanced Installation Meter 2 Operation Manual Download Page 94

Page: 94 / 108

Page 94

AIM 2 Operation Manual

Viewing Records

You can view records for tests performed on the AIM, including EIV, EIV Plus, Guided Mode,

and Transponder Survey, as well as screenshots. You can select a record to view from a list of

all records on the AIM, or view records by account number.

1. Press

CONFIG

to go to the

CONFIGURATION

screen.

2. Highlight

Records

and press

SELECT

to go to

the

RECORDS MAIN

screen.

3. Highlight

View All Records

and press

SELECT

to go to the

VIEW RECORDS

screen.

Alternatively, if you want to view records for a

selected account number, do the following:

• Highlight

View By Account Number

and press

SELECT

to go to the

VIEW

RECORDS BY ACCOUNT

screen.

• Highlight the account number you want

to view and press

SELECT

to go to the

VIEW RECORDS

screen.

Summary of Contents for Advanced Installation Meter 2













































































































Search results

Summary of Contents for Advanced Installation Meter 2

Reviews:

Related manuals for Advanced Installation Meter 2

Brands by name

Popular brands

DirecTV Advanced Installation Meter 2, Operation Manual

Search results

Summary of Contents for Advanced Installation Meter 2

Reviews:

Related manuals for Advanced Installation Meter 2

Brands by name

Popular brands