DirecTV Advanced Installation Meter 2 Operation Manual Download Page 7

Page: 7 / 108

Page 7

AIM 2 Operation Manual

www.trilithic.com

Where to Get Technical Support

When you need instructions for using the AIM, your first resource for help is this manual. If you

cannot find the information you need, you can:

•

Go to the DIRECTV Satellite Installer website or other websites provided by DIRECTV.

DIRECTV websites contain product specifications and information, tips, release

information, marketing information, Frequently Asked Questions (FAQs), bulletins and

other technical information. You can also check these websites for product updates.

•

Contact

Solid Signal at 877.312.4547 or email [email protected].

For quicker support response when calling or sending e-mail, please provide the following

information:

• Your name and your company name
•

The technical point of contact (name, phone number, e-mail)

•

The AIM serial number, firmware and hardware version numbers

• A detailed description of the problem you are having, including any error or information

messages

General Information

Chapter 1

Summary of Contents for Advanced Installation Meter 2













































































































Search results

Summary of Contents for Advanced Installation Meter 2

Reviews:

Related manuals for Advanced Installation Meter 2

Brands by name

Popular brands

DirecTV Advanced Installation Meter 2, Operation Manual

Search results

Summary of Contents for Advanced Installation Meter 2

Reviews:

Related manuals for Advanced Installation Meter 2

Brands by name

Popular brands