DirecTV Advanced Installation Meter 2 Operation Manual Download Page 53

Page: 53 / 108

Page 53

AIM 2 Operation Manual

Task A. Installation Setup

Set up the job for the installation. See the

Starting a Job

section in

Chapter 5

2. From the

HOME

screen, press

INSTALL

The

PRE-CONFIGURE ODU

screen appears

showing the default azimuth and elevation

coordinates for the job. If appropriate, the

default tilt coordinate also appears.

3. Perform the ODU site survey. Using the AIM

azimuth and elevation coordinates, confirm that

the selected location has a clear line-of-sight

to the supported orbital slots (see the ODU

Installation Tasks table on the previous page).

Install the ODU according to the DIRECTV

procedure.

Connect the AIM’s ODU F Connector to the

ODU’s LNB output.

6. Press

NEXT

on the

PRE CONFIGURE ODU

screen.

• If the installation includes two ODUs, the

SELECT ODU

screen appears. Highlight

the ODU to align and press

SELECT

continue.

The default coordinates for the job are based on the ODU type

and zip code selected for the job.

Summary of Contents for Advanced Installation Meter 2













































































































Search results

Summary of Contents for Advanced Installation Meter 2

Reviews:

Related manuals for Advanced Installation Meter 2

Brands by name

Popular brands

DirecTV Advanced Installation Meter 2, Operation Manual

Search results

Summary of Contents for Advanced Installation Meter 2

Reviews:

Related manuals for Advanced Installation Meter 2

Brands by name

Popular brands