DirecTV Advanced Installation Meter 2 Operation Manual Download Page 99

Page: 99 / 108

Page 99

AIM 2 Operation Manual

5. To delete all records for an account, do

the following on the

VIEW RECORDS BY

ACCOUNT

screen.

• Highlight the account number and press

OPTIONS

• On the

Options

window, highlight

Delete...

and press

• Highlight the type of records to delete

and press

. You can select

Delete

All Records

to delete all records for

the account, or select a specific type of

records to delete.

• Go to Step 6.

On the message that appears to confirm the

deletion, press

The records are deleted. Press

again to

acknowledge the deletion, and the

RECORDS

MAIN, VIEW RECORDS

, or

VIEW RECORDS

BY ACCOUNT

screen appears.

Summary of Contents for Advanced Installation Meter 2













































































































Search results

Summary of Contents for Advanced Installation Meter 2

Reviews:

Related manuals for Advanced Installation Meter 2

Brands by name

Popular brands

DirecTV Advanced Installation Meter 2, Operation Manual

Search results

Summary of Contents for Advanced Installation Meter 2

Reviews:

Related manuals for Advanced Installation Meter 2

Brands by name

Popular brands