DirecTV Advanced Installation Meter 2 Operation Manual Download Page 106

Page: 106 / 108

Page 106

AIM 2 Operation Manual

Update Firmware from the Internet

The AIM can update firmware from an Ethernet

connection or via Wi-Fi.

Make sure the Ethernet connection has been set

up and you have connected a Ethernet cable to the

port on the AIM.

If using Wi-Fi, make sure the Wi-fi network has

been set up. The AIM will then connect to the

network.

1. Select the

Select update from Internet

option

and press

SELECT

. The AIM connects to the

update server and shows the available updates.

2. Select the update version and press

SELECT.

The firmware update process begins. A

message appears when the firmware update is

complete and the meter automatically restarts

with the new firmware.

Update Firmware from a USB Flash

Drive

Insert the USB flash drive that contains the

firmware update into the USB port on the meter.

Wait 15 seconds, then select the

Select update

from USB

option and press

SELECT

The available updates on the USB flash drive

appear. Choose which update you want to use

and press

SELECT

The firmware update process begins. A

message appears when the firmware update is

complete and the meter automatically restarts with the new firmware.

3. After the meter turns on and the

HOME

screen appears, you can remove the USB flash

drive from the USB port.

Summary of Contents for Advanced Installation Meter 2













































































































Search results

Summary of Contents for Advanced Installation Meter 2

Reviews:

Related manuals for Advanced Installation Meter 2

Brands by name

Popular brands

DirecTV Advanced Installation Meter 2, Operation Manual

Search results

Summary of Contents for Advanced Installation Meter 2

Reviews:

Related manuals for Advanced Installation Meter 2

Brands by name

Popular brands