12
Operation
Setting Mode
●
Settings can be viewed on the printer’s operation panel.
●
Settings can be changed on the status monitor of the computer.
"Setting using the operation panel"
（
A
page 16
）
Cleaning
●
For setting during cleaning of the card feed roller or magnetic head.
Setting values
●
Rollers
Select this value when cleaning the card feed roller.
●
MG
Select this value when cleaning the magnetic head.
Counter Reset
●
Resets the free counter and error counter.
Test Print
●
Prints the printer’s built-in test pattern, or the different setting values.
●
When system troubles occur, printing can be performed using settings
on the printer or computer by operating only the printer.
Setting values
●
Test Print: Test Pattern, Printer Setting, Network, Lami Setting
Down load
●
Updates the firmware.
Transport Mode
●
For setting the transport mode.
Media
●
Displays the settings of the printing media.
Setting values
●
Ink Type: YMCK, YMCKPO, YMCKK, YMCKUV
Set according to the type of ink ribbon.
●
Film Type: 1000, 750
Set according to the type of retransfer film.
●
Card Thickness: Standard, Thin
Set according to the thickness of the card.
Standard: Supports card thickness of 0.76 mm
Thin: Supports card thickness of 0.25 mm
●
Displays the printing settings.
Setting values
●
YMC Level: -3, -2, -1, 0, 1, 2, 3
For setting the YMC (color) concentration level.
Selecting a larger value increases the concentration level.
●
Black Level: -3, -2, -1, 0, 1, 2, 3
For setting the K(Black) concentration level.
Selecting a larger value increases the concentration level.
●
Black Mode: Standard, Fine
For setting the K(Black) printing mode.
If the characters still appear faded after raising the
［
BlackLevel
］
,
set to
［
Fine
］
.
However, printing time required will be longer than the
［
Stand-
ard
］
setting.
●
UV Level: -3, -2, -1, 0, 1, 2, 3
For setting the UV ink concentration level.
Selecting a larger value increases the concentration level.
During UV printing, card warpage may increase if the card has a
low heat resistance or under an environment with high tempera-
ture.
●
PO Level: -3, -2, -1, 0, 1, 2, 3
For setting the concentration level of the peel-off ink.
Selecting a larger value increases the concentration level.
Retransfer
●
Displays the retransfer mode settings.
Setting values
●
Temp Level: -2, -1, 0, 1, 2
For setting the retransfer roller temperature.
Selecting a larger value increases the temperature.
Retransfer may fail depending on the card used. If retransfer fails,
raise the setting to the next higher value.
A higher retransfer roller temperature helps to enhance card re-
transfer, but the stronger heat may also cause the card to deform.
If the printer is not initialized after changing the temperature set-
ting, temperature is adjusted after the printing operationstarts.
●
Speed (Front): -3, -2, -1, 0, 1, 2
For setting the surface retransfer speed.
Selecting a larger value increases the speed.
Retransfer may not be successful for some parts of thecard de-
pending on the card used. Lowering the setting value helps to en-
hance retransfer, but the stronger heat may also cause the card to
deform.
●
Speed (Back): -3, -2, -1, 0, 1, 2
For setting the rear surface retransfer speed.
Selecting a larger value increases the speed.
Some types of cards may warp during double-sided printing. If
card warpage occurs, raise the setting to the next higher value.
●
MG Peel Mode: Standard, MG Stripe
For setting the method for peeling the retransfer film.
●
Standby Mode: Front wait, Back wait
For setting the laminator standby position.
Select whether to standby at the front or rear surface during dou-
ble-sided printing.
Bend Remedy
●
Displays the warpage correction mode settings.
Setting values
●
Temp Level: -5, -4, -3, -2, -1, 0, off
For setting the warpage correction roller temperature.
Selecting a larger value increases the temperature.
If the printer is not initialized after changing the temperature set-
ting, temperature is adjusted after the printing operationstarts.
●
Speed: -2, -1, 0, 1, 2
For setting the warpage correction mode speed.
Selecting a larger value increases the speed.
Heat Roller
●
Displays the settings of the power save mode or low temperature
standby mode.
Setting values
●
Power Saving: 5 mins, 10 mins, 15 mins, 20 mins, 25 mins,
30mins, 45 mins, 60 mins, off
For setting the time of the power save mode.
While in the [Ready] mode, if the printer is not operated during a
specific time interval, the retransfer roller, warpage correction
roller, and backlight of the operation panel are turned off to save
power.
●
HR Control: Off, On
Summary of Contents for EDIsecure X ID 8300
Page 14: ...14 Operation ...
Page 15: ...15 Operation ...
