Dell Precision Workstation M6400 Service Manual Download Page 53

Page: 53 / 81

LED and CCFL Displays: Dell Precision M6400 Service Manual

file:///T|/htdocs/systems/wsm6400/en/sm/displayb.htm[11/16/2012 10:27:02 AM]

1 M2.5 x 5-mm screws (2) on left hinge 2 M2.5 x 5-mm screws (2) on right hinge

9. Pull the wireless antenna cables up through the computer.

10. Remove the LVDS captive screw.

11. Disconnect and unroute the display cable.

12. Disconnect and unroute the ambient-light sensor cable.

13. Lift the display off the base assembly.

1 ambient-light sensor cable 2 base assembly
3 display assembly

4 antenna cables

5 LVDS captive screw

6 display cable

Replacing the Display Assembly

CAUTION:

Before working inside your computer, read the safety information that shipped with your

computer. For additional safety best practices information, see the Regulatory Compliance Homepage on

www.dell.com at: www.dell.com/regulatory_compliance.

1. Align the hinges with the holes in the base assembly, and lower the display into place.

2. Replace the two M2.5 x 5-mm screws in the right hinge and the two M2.5 x 5-mm screws in the left hinge.

3. Route and connect the ambient-light sensor cable.

4. Route and connect the display cable.

Summary of Contents for Precision Workstation M6400


















































































Search results

Summary of Contents for Precision Workstation M6400

Reviews:

Related manuals for Precision Workstation M6400

Brands by name

Popular brands

Dell Precision Workstation M6400, Service Manual

Search results

Summary of Contents for Precision Workstation M6400

Reviews:

Related manuals for Precision Workstation M6400

Brands by name

Popular brands