Dell Precision Workstation M6400 Service Manual Download Page 36

Page: 36 / 81

Coin-Cell Battery: Dell Precision M6400 Service Manual

file:///T|/htdocs/systems/wsm6400/en/sm/coinbatt.htm[11/16/2012 10:26:43 AM]

Back to Contents Page

Coin-Cell Battery

Dell Precision™ M6400 Service Manual

Removing the Coin-Cell Battery

Replacing the Coin-Cell Battery

Removing the Coin-Cell Battery

CAUTION:

Before working inside your computer, read the safety information that shipped with your

computer. For additional safety best practices information, see the Regulatory Compliance Homepage on

www.dell.com at: www.dell.com/regulatory_compliance.

1. Follow the procedures in

Before Working on Your Computer

2. Remove the base assembly cover (see

Removing the Base Assembly Cover

3. Slide the coin-cell battery out of the mylar sleeve.

4. Disconnect the coin-cell battery cable from the system board.

coin-cell battery

coin-cell battery cable

Replacing the Coin-Cell Battery

CAUTION:

Before working inside your computer, read the safety information that shipped with your

computer. For additional safety best practices information, see the Regulatory Compliance Homepage on

www.dell.com at: www.dell.com/regulatory_compliance.

1. Connect the coin-cell battery cable to the system board.

2. Slide the coin-cell battery into the mylar sleeve.

Summary of Contents for Precision Workstation M6400


















































































Search results

Summary of Contents for Precision Workstation M6400

Reviews:

Related manuals for Precision Workstation M6400

Brands by name

Popular brands

Dell Precision Workstation M6400, Service Manual

Search results

Summary of Contents for Precision Workstation M6400

Reviews:

Related manuals for Precision Workstation M6400

Brands by name

Popular brands