Dell Precision Workstation M6400 Service Manual Download Page 29

Page: 29 / 81

WWAN Card: Dell Precision M6400 Service Manual

file:///T|/htdocs/systems/wsm6400/en/sm/wwan.htm[11/16/2012 10:26:34 AM]

Back to Contents Page

WWAN Card

Dell Precision™ M6400 Service Manual

Removing a WWAN Card

Replacing a WWAN Card

CAUTION:

Before working inside your computer, read the safety information that shipped with your

computer. For additional safety best practices information, see the Regulatory Compliance Homepage on

www.dell.com at: www.dell.com/regulatory_compliance.

NOTICE:

Insert a WWAN card or FCM only into the slot labeled WWAN/FCM.

Removing a WWAN Card

1. Follow the procedures in

Before Working on Your Computer

2. Remove the base assembly cover (see

Removing the Base Assembly Cover

3. Disconnect the antenna cables from the card.

4. Remove the M2 x 3-mm screw. The card pops up at a 45-degree angle.

antenna cables (2)

WWAN card

M2 x 3-mm screw

5. Slide the card out of the card connector on the system board.

Summary of Contents for Precision Workstation M6400


















































































Search results

Summary of Contents for Precision Workstation M6400

Reviews:

Related manuals for Precision Workstation M6400

Brands by name

Popular brands

Dell Precision Workstation M6400, Service Manual

Search results

Summary of Contents for Precision Workstation M6400

Reviews:

Related manuals for Precision Workstation M6400

Brands by name

Popular brands