Dell Precision Workstation M6400 Service Manual Download Page 17

Page: 17 / 81

Working on Your Computer: Dell Precision M6400 Service Manual

file:///T|/htdocs/systems/wsm6400/en/sm/before.htm[11/16/2012 10:26:20 AM]

8. Turn the computer topside up, open the display, and press the power button to ground the system board.

After Working on Your Computer

After you have completed the replacement procedures, ensure you connect the external devices, cards, and cables before

turning on your computer.

NOTE:

To avoid damage to the computer, use only the battery designed for this particular Dell computer. Do not use

batteries designed for other Dell computers.

1. Connect external devices, replace cards, and connect telephone or network cables to your computer.

2. Slide the battery into the battery bay and snap it into place.

3. Connect your computer and attached devices to their electrical outlets.

4. Turn on your computer.

Back to Contents Page

Summary of Contents for Precision Workstation M6400


















































































Search results

Summary of Contents for Precision Workstation M6400

Reviews:

Related manuals for Precision Workstation M6400

Brands by name

Popular brands

Dell Precision Workstation M6400, Service Manual

Search results

Summary of Contents for Precision Workstation M6400

Reviews:

Related manuals for Precision Workstation M6400

Brands by name

Popular brands