Dell Precision Workstation M6400 Service Manual Download Page 54

Page: 54 / 81

LED and CCFL Displays: Dell Precision M6400 Service Manual

file:///T|/htdocs/systems/wsm6400/en/sm/displayb.htm[11/16/2012 10:27:02 AM]

5. Replace the LVDS captive screw.

6. Thread the WWAN, WLAN, and WPAN antenna cables through the computer.

7. Replace the keyboard (see

Replacing the Keyboard

8. Replace the LED cover (see

Replacing the LED Cover

9. Close the display and turn the computer upside down.

10. Replace the two M2.5 x 8-mm screws on the back of the base assembly and the two M2.5 x 8-mm screws on the

bottom of the base assembly.

11. Route the wireless antenna cables. Ensure you route the cables under each tab in the routing channels.

12. Depending on the cards in your computer configuration, connect the antenna cables to the WWAN, WLAN, and WPAN

cards (see

Replacing a WWAN Card

Replacing the WLAN/WiMax Card

, and

Replacing a WPAN Card

Place any unused antenna cables in the base assembly cable holders next to the card slot.

13. Replace the base assembly cover (see

Replacing the Base Assembly Cover

14. Follow the procedures in

After Working on Your Computer

Removing the Display Cover

CAUTION:

Before working inside your computer, read the safety information that shipped with your

computer. For additional safety best practices information, see the Regulatory Compliance Homepage on

www.dell.com at: www.dell.com/regulatory_compliance.

1. Follow the instructions in

Before Working on Your Computer

2. Remove the display assembly (see

Removing the Display Assembly

3. Remove the display bezel (see

Removing the Display Bezel

NOTE:

It is not necessary to remove the brackets from the display panels in the next step.

4. Remove the display panel from the display cover (see

Removing the Display Panel

Replacing the Display Cover

CAUTION:

Before working inside your computer, read the safety information that shipped with your

computer. For additional safety best practices information, see the Regulatory Compliance Homepage on

www.dell.com at: www.dell.com/regulatory_compliance.

1. Remove the tape from the cables that are taped to the display cover.

2. Replace the display panel (see

Replacing the Display Panel

3. Replace the display bezel (see

Replacing the Display Bezel

4. Replace the display assembly (see

Replacing the Display Assembly

5. Follow the procedures in

After Working on Your Computer

Summary of Contents for Precision Workstation M6400


















































































Search results

Summary of Contents for Precision Workstation M6400

Reviews:

Related manuals for Precision Workstation M6400

Brands by name

Popular brands

Dell Precision Workstation M6400, Service Manual

Search results

Summary of Contents for Precision Workstation M6400

Reviews:

Related manuals for Precision Workstation M6400

Brands by name

Popular brands