Dell Precision Workstation M6400 Service Manual Download Page 27

Page: 27 / 81

WLAN/WiMax Card: Dell Precision M6400 Service Manual

file:///T|/htdocs/systems/wsm6400/en/sm/wlan.htm[11/16/2012 10:26:31 AM]

Back to Contents Page

WLAN/WiMax Card

Dell Precision™ M6400 Service Manual

Removing the WLAN/WiMax Card

Replacing the WLAN/WiMax Card

CAUTION:

Before working inside your computer, read the safety information that shipped with your

computer. For additional safety best practices information, see the Regulatory Compliance Homepage on

www.dell.com at: www.dell.com/regulatory_compliance.

NOTICE:

Insert a WLAN or WiMax card only into the slot labeled WLAN/WiMax.

Removing the WLAN/WiMax Card

1. Follow the procedures in

Before Working on Your Computer

2. Remove the base assembly cover (see

Removing the Base Assembly Cover

3. Disconnect the antenna cables from the card.

4. Remove the M2 x 3-mm screw. The card will pop up at a 45-degree angle.

antenna cables (3)

M2 x 3-mm screw

WLAN/WiMax card

5. Slide the card out of the card connector on the system board.

Summary of Contents for Precision Workstation M6400


















































































Search results

Summary of Contents for Precision Workstation M6400

Reviews:

Related manuals for Precision Workstation M6400

Brands by name

Popular brands

Dell Precision Workstation M6400, Service Manual

Search results

Summary of Contents for Precision Workstation M6400

Reviews:

Related manuals for Precision Workstation M6400

Brands by name

Popular brands