Dell Precision Workstation M6400 Service Manual Download Page 46

Page: 46 / 81

LED and CCFL Displays: Dell Precision M6400 Service Manual

file:///T|/htdocs/systems/wsm6400/en/sm/displayb.htm[11/16/2012 10:27:02 AM]

1 left side of bezel

2 top of bezel

3 right side of bezel 4 M2.5 x 5-mm screws (2)
5 display assembly

6 bottom of bezel

Replacing the Display Bezel

CAUTION:

Before working inside your computer, read the safety information that shipped with your

computer. For additional safety best practices information, see the Regulatory Compliance Homepage on

www.dell.com at: www.dell.com/regulatory_compliance.

1. Angle the bottom of the bezel in under the hinges, then firmly press the center of the bottom of the bezel into place.

2. Push in on the left and right sides of the bezel and ensure the tabs connect inside the display cover.

3. Firmly press along the top to snap the bezel into place.

4. Replace the two M2.5 x 5-mm screws on the bottom of the bezel.

Summary of Contents for Precision Workstation M6400


















































































Search results

Summary of Contents for Precision Workstation M6400

Reviews:

Related manuals for Precision Workstation M6400

Brands by name

Popular brands

Dell Precision Workstation M6400, Service Manual

Search results

Summary of Contents for Precision Workstation M6400

Reviews:

Related manuals for Precision Workstation M6400

Brands by name

Popular brands