Dell Precision Workstation M6400 Service Manual Download Page 30

Page: 30 / 81

WWAN Card: Dell Precision M6400 Service Manual

file:///T|/htdocs/systems/wsm6400/en/sm/wwan.htm[11/16/2012 10:26:34 AM]

WWAN card

card connector

Replacing a WWAN Card

NOTICE:

The connectors are keyed to ensure correct insertion. If you feel resistance, check the connectors

on the card and on the system board, and realign the card.

NOTICE:

To avoid damage to the WWAN card, ensure the cables are not under the card when you replace

it.

NOTICE:

Insert a WWAN card or FCM only into the slot labeled WWAN/FCM.

1. Slide the card into the connector labeled WWAN/FCM.

2. Press the card down and hold it in place.

3. Replace the M2 x 3-mm screw.

4. Connect the white antenna cable to the connector labeled "main" (white triangle), and connect the black antenna cable

to the connector labeled "aux" (black triangle).

5. Replace the base assembly cover (see

Replacing the Base Assembly Cover

6. Follow the procedures in

After Working on Your Computer

Back to Contents Page

Summary of Contents for Precision Workstation M6400


















































































Search results

Summary of Contents for Precision Workstation M6400

Reviews:

Related manuals for Precision Workstation M6400

Brands by name

Popular brands

Dell Precision Workstation M6400, Service Manual

Search results

Summary of Contents for Precision Workstation M6400

Reviews:

Related manuals for Precision Workstation M6400

Brands by name

Popular brands