Dell Precision Workstation M6400 Service Manual Download Page 51

Page: 51 / 81

LED and CCFL Displays: Dell Precision M6400 Service Manual

file:///T|/htdocs/systems/wsm6400/en/sm/displayb.htm[11/16/2012 10:27:02 AM]

5. Follow the procedures in

After Working on Your Computer

Removing the Microphone/Camera Board

CAUTION:

Before working inside your computer, read the safety information that shipped with your

computer. For additional safety best practices information, see the Regulatory Compliance Homepage on

www.dell.com at: www.dell.com/regulatory_compliance.

NOTE:

Camera is optional and may not be included on your computer.

1. Follow the instructions in

Before Working on Your Computer

2. Remove the display bezel (see

Removing the Display Bezel

3. Disconnect the cable from the microphone/camera board.

4. Remove the two M2.5 x 5-mm screws, and remove the microphone/camera board.

1 display cover

2 microphone/camera board

3 cable connector

4 cable

5 M2.5 x 5-mm screws (2)

Replacing the Microphone/Camera Board

CAUTION:

Before working inside your computer, read the safety information that shipped with your

computer. For additional safety best practices information, see the Regulatory Compliance Homepage on

www.dell.com at: www.dell.com/regulatory_compliance.

1. Lift the cable out of the way and place the microphone/camera board in the display cover.

2. Connect the cable to the microphone/camera board.

3. Replace the two M2.5 x 5-mm screws.

4. Replace the display bezel (see

Replacing the Display Bezel

Summary of Contents for Precision Workstation M6400


















































































Search results

Summary of Contents for Precision Workstation M6400

Reviews:

Related manuals for Precision Workstation M6400

Brands by name

Popular brands

Dell Precision Workstation M6400, Service Manual

Search results

Summary of Contents for Precision Workstation M6400

Reviews:

Related manuals for Precision Workstation M6400

Brands by name

Popular brands