Dell Precision Workstation M6400 Service Manual Download Page 49

Page: 49 / 81

LED and CCFL Displays: Dell Precision M6400 Service Manual

file:///T|/htdocs/systems/wsm6400/en/sm/displayb.htm[11/16/2012 10:27:02 AM]

1 underside of display panel 2 cables (2)
3 cable connector

4 cable connector

5 release tabs

7. Remove two M2 x 3-mm screws along the top of the panel to remove the bracket.

1 display panel 2 M2 x 3-mm screws (2)
3 bracket

Replacing the Display Panel

CAUTION:

Before working inside your computer, read the safety information that shipped with your

computer. For additional safety best practices information, see the Regulatory Compliance Homepage on

www.dell.com at: www.dell.com/regulatory_compliance.

1. Replace the two M2 x 3-mm screws to secure the bracket to the display panel.

2. Connect the cables to the connectors on the back of the display panel.

3. Place the display panel in display cover.

4. Replace the ten M2 x 3-mm screws that secure the display panel to the display cover (four screws on each side and

Summary of Contents for Precision Workstation M6400


















































































Search results

Summary of Contents for Precision Workstation M6400

Reviews:

Related manuals for Precision Workstation M6400

Brands by name

Popular brands

Dell Precision Workstation M6400, Service Manual

Search results

Summary of Contents for Precision Workstation M6400

Reviews:

Related manuals for Precision Workstation M6400

Brands by name

Popular brands